How to Winterize Your Aquavoss Cold PlungeUpdated 19 days ago
Applies to:
- Aquavoss AV-1 (Cold Plunge)
- Aquavoss AV-2 (Cold Side Only)
Overview
If your Aquavoss cold plunge will be exposed to freezing temperatures (32°F / 0°C or below), proper winterization is critical to prevent damage to plumbing, pumps, and the chiller system. The only Aquavoss-approved method is to drain the unit, remove the filter and chiller, and clear all water from the plumbing, using the 5 steps below.
- If you live in a warm climate where temperatures don’t reach freezing, you don’t need to winterize.
- AV-2 owners only need to winterize the cold side. Keep the hot tub running.
⚠️ Important: Any other approach (such as running the pump continuously or attempting to operate through freezing conditions) is done at the owner’s risk. Freeze damage caused by improper winterization is not covered under warranty.
When You Should Winterize
You should winterize if:
- Temperatures are expected to fall to 32°F (0°C) or below
- The unit will be unattended during cold weather
- You cannot verify daily operation and circulation
- There is any risk of power outages or equipment shutdown
Even a short freeze event can cause severe damage if water remains in plumbing.
Tools & Supplies Needed
- Wet/dry shop vacuum with blow and vacuum capability (a 5-gallon model works well)
- Towels
- Basic hand tools (if needed for unions or clamps)
- Bucket or container for residual water
How to Winterize: The 5 Steps
Following these instructions carefully will protect your unit from damage and make spring start-up easy and trouble-free.
1. Power Off & Drain
- Turn the cold side OFF at the control panel.
- Unplug the unit before you begin.
- Confirm the cold plunge cannot power on while empty.
- Attach a hose or use a pump if necessary, and drain all the water from the cold plunge completely.
- Remove any remaining water with towels or a shop vac.

2. Remove Filter
- Take out the paper filter cartridge.
- Remove the clear filter housing/canister assembly.
- Drain all water from the housing.
- Dry both thoroughly and store them in a dry, warm place for the winter.

3. Remove the Chiller
- Shut any isolation valves if present.
- Disconnect the inlet and outlet hoses and allow them to drain completely.
- Unplug the chiller from the circulation pump, ozone system, and control panel.
- Move the chiller indoors to a dry, warm, above-freezing location for the winter.
The chiller must not be left outdoors with water inside during freezing conditions.

4. Remove Remaining Water
The goal is to remove all water from plumbing and components.
- Remove the metal grate and mesh filter so air can reach the plumbing behind them.
- Set the shop vac to BLOW.
- Blow air through every opening, starting with the jets at the top and working downward:
- All four jets
- The metal grate (suction) opening
- The drain
- Any disconnected hose ends
- Switch the shop vac to VACUUM.
- Vacuum the remaining water from:
- The filter opening
- The inlet hose and outlet hose
- The jet openings and drain area
- Replace the metal grate and mesh filter.
Tip: Use a rag to seal around the vacuum hose to increase suction and pull trapped water out.

5. Dry the Cold Plunge
- Thoroughly dry the acrylic shell with a clean towel.
- Make sure no moisture remains in any corners.
- Remove any standing water in equipment areas.
- Leave the cabinet open briefly (if safe) to allow moisture to evaporate.
- Reinstall cabinet panels if removed, and secure the cover.
Your unit is now winterized.
Spring Startup (Recommissioning)
When temperatures are safely above freezing:
- Reinstall the chiller and reconnect hoses and power/control connections.
- Reinstall filter housing and filter.
- Fill the plunge to 0.5–1 inch above the highest jet.
- Restore power only once the water is above all the jets.
- Check for leaks and proper circulation before use.
Frequently Asked Questions
Can I run the cold plunge during winter?
Only if temperatures remain above freezing and the unit is monitored. Persistent freezing conditions require winterization.
Can I leave the chiller outside if I drain it?
No. Residual moisture can freeze and cause damage. The chiller should be stored indoors.
Need Help?
Need help? Contact the Aquavoss Technical Service Team at [email protected] or call or text 213-459-6534.